6MDAN-8P0111
4.75 (4)
Click a star to rate this product
- 4.75 (4)
- Click a star to rate this product
2HP MD60 Drive with Filter
* Learn More About Product Conditions
* Posted pricing available for website purchases only.
Product Conditions
New Surplus Factory Package: A completely unused product that is in the original factory package. The package may have been opened for the purpose of pictures, but the product has never been used or installed.
New Surplus AX Control Package: A completely unused product that has been removed from the original factory package. Often due to shelf wear or previous shipping, the factory package is not adequate and must be replaced with an ideal AX Control product package.
Reconditioned: All products that qualify as reconditioned have completed AX Control's thorough and detailed QA process and meet the requirements of excellent working condition and excellent cosmetic condition.
Product Description
6MDAN-8P0111 is a 230 V, 50/60 Hz, 1-phase MD60 Drive that is manufactured by Reliance Electric. The output current is 8.0 A, the horsepower is 2.0 HP, and the output power is 1.5 kW. There is an integral EMC filter. The frame size is B.There are a number of fault codes on the MD60 drive. F41 (phase UV short), F42 (phase UW short), F43 (phase VW short) all indicate that excessive current has been detected between two output terminals. To correct this fault, check the motor and the drive output terminal wiring for a shorted condition, or replace the drive if the fault cannot be cleared. F48 is a parameters defaulted fault that indicates that the drive was commanded to write default values to EEPROM. To correct this fault, clear the fault or cycle the drive power and program the drive parameters as needed. F63 is an SW overcurrent fault that indicates that the SW current trip has been exceeded. To correct this fault, check the load requirements and the SW current trip setting.
F64 is a drive overload fault that indicates that the drive has overloaded at higher than 150% and/or longer than 1 minute. To correct this fault, reduce the load on the drive or extend the acceleration time. F70 is a power unit fault that indicates that drive power has failed. To correct this fault, cycle the drive power, or replace the drive if the fault cannot be cleared. F81 is a communications loss fault that indicates that the RS485 port has stopped communicating. To correct this fault, check wiring to the port, check the connection, and/or turn off using the comm loss action. F100 is the parameter checksum fault, which indicates that the checksum read from the board does not match the calculated checksum. To correct this fault, reset the default parameters. F122 is an I/O board failure, which indicates that the drive control and I/O section have experienced a failure. To correct this part, first cycle drive power, and if the fault cannot be cleared, replace the drive.
6MDAN-8P0111 Technical Specifications
| Manufacturer | Reliance Electric |
| Series | MD60 |
| Part Number | 6MDAN-8P0111 |
| HP | 2 HP |
| Input Voltage | 180-264 VAC |
| Enclosure | NEMA 1 or Chassis |
| Hz | 48-63Hz |
| kW | 1.5kW |
| Filter/No Filter | Internal Filter |
| Labeling | UL Listed, IEC Certified |
Frequently Asked Questions about 6MDAN-8P0111
What is the output current for 6MDAN-8P0111?
What frame size is the MD60 6MDAN-8P0111?
What is the shipping weight of a Reliance Electric MD60 6MDAN-8P0111 drive?
Which parameters cannot be adjusted on a 6MDAN-8P0111?
What is the default jog frequency on a 6MDAN-8P0111 MD60 drive?
6MDAN-8P0111 Technical Specifications
| Manufacturer | Reliance Electric |
| Series | MD60 |
| Part Number | 6MDAN-8P0111 |
| HP | 2 HP |
| Input Voltage | 180-264 VAC |
| Enclosure | NEMA 1 or Chassis |
| Hz | 48-63Hz |
| kW | 1.5kW |
| Filter/No Filter | Internal Filter |
| Labeling | UL Listed, IEC Certified |
Product Description
6MDAN-8P0111 is a 230 V, 50/60 Hz, 1-phase MD60 Drive that is manufactured by Reliance Electric. The output current is 8.0 A, the horsepower is 2.0 HP, and the output power is 1.5 kW. There is an integral EMC filter. The frame size is B.There are a number of fault codes on the MD60 drive. F41 (phase UV short), F42 (phase UW short), F43 (phase VW short) all indicate that excessive current has been detected between two output terminals. To correct this fault, check the motor and the drive output terminal wiring for a shorted condition, or replace the drive if the fault cannot be cleared. F48 is a parameters defaulted fault that indicates that the drive was commanded to write default values to EEPROM. To correct this fault, clear the fault or cycle the drive power and program the drive parameters as needed. F63 is an SW overcurrent fault that indicates that the SW current trip has been exceeded. To correct this fault, check the load requirements and the SW current trip setting.
F64 is a drive overload fault that indicates that the drive has overloaded at higher than 150% and/or longer than 1 minute. To correct this fault, reduce the load on the drive or extend the acceleration time. F70 is a power unit fault that indicates that drive power has failed. To correct this fault, cycle the drive power, or replace the drive if the fault cannot be cleared. F81 is a communications loss fault that indicates that the RS485 port has stopped communicating. To correct this fault, check wiring to the port, check the connection, and/or turn off using the comm loss action. F100 is the parameter checksum fault, which indicates that the checksum read from the board does not match the calculated checksum. To correct this fault, reset the default parameters. F122 is an I/O board failure, which indicates that the drive control and I/O section have experienced a failure. To correct this part, first cycle drive power, and if the fault cannot be cleared, replace the drive.
